Patch panels

X: empty hole

G: SMA connector used as ground lug

F: pulser fiber

	Outside view:
St2, top:	50 42 34 G 33 41 49 48 40 32 X 31 39 47 46 38 30 26 29 37 45 44 36 28 25 27 35 43 X F F
St2, bottom:	X X F 8 16 24 X 23 15 7 6 14 22 X 21 13 5 4 12 20 X 19 11 3 2 10 18 X 17 9 1
St1, top:	80 78 70 G 69 77 79 76 74 66 X 65 73 75 72 56 62 46 61 55 71 68 52 58 45 57 51 67 64 48 54 42 53 47 63 60 44 50 41 49 43 59 F F F
St1, bottom:	X F F 24 40 30 38 29 39 23 20 36 26 37 25 35 19 16 32 22 34 21 31 15 12 28 18 33 17 27 11 8 6 14 X 13 5 7 4 2 10 X 9 1 3

Pulser fibers:

• St2 top serves 1-17 and 18-33, St2 bottom serves 34-50
• St1 top serves 1-16, 17-32, and 49-64, St1 bottom serves 33-48 and 65-80

Distribution boards

All mappings are shown in the orientation where the distribution board text faces up.

X: unused

A+B: two daisy-chained preamps

	Outside view:
Bias channel numbers:	1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Bias ribbon pinout:	J1:1 J1:2 J1:3 J1:4 J1:5 J1:6 J1:7 J1:8 J2:1 J2:2 J2:3 J2:4 J2:5 J2:6 J2:7 J2:8 J3:1 J3:2 J3:3 J3:4 J3:5 J3:6 J3:7 J3:8

	Outside view:
St2, top:	26 38 37 25 28 40 39 27 30 42 41 29 32 44 43 31 34 46 45 33 36 48+50 47+49 35
St2, bottom:	23 11 12 24 21 9 10 22 19 7 8 20 17 5 6 18 15 3 4 16 13 1 2 14
St1, bottom:	39 37 38 40 35 33 34 36 31 29 30 32 27 25 26 28 23 21 22 24 X X X X
St2, 2nd from bottom:	19 17 18 20 15 13 14 16 11 9 10 12 7 5 6 8 3 1 2 4 X X X X
St1, 3rd from bottom:	64 62 61 63 68 66 65 67 72 70 69 71 76 74 73 75 80 78 77 79 X X X X
St1, 4th from bottom:	44 42 41 43 48 46 45 47 52 50 49 51 56 54 53 55 60 58 57 59 X X X X

10-pin connector pin numbering (looking at a board connector, with the key facing down):

2	4	6	8	10
1	3	5	7	9

Preamp pinout:

1. Bias
2. Ground
3. N.C.
4. N.C.
5. RTD bias
6. N.C. (would be temp/humidity sensor)
7. RTD output
8. RTD ground
9. +6V
10. Ground